Mehedi Telecom

MOST WELCOME TO OUR COMMUNITY MY BROTHER / SISTERS

" ENJOY STAY HERE "

= WELCOME TO SAVAR MOBILE FORUM =

= PLEASE REGISTER FOR WHICH CAN NOT LOG-IN =
= WE ARE GLAD THAT IF YOU WANT TO SHARE EXPERIENCES WITH SCIENCE AND WE HERE =


= WARM GREETINGS =
Mehedi Telecom

All HTC,LG,NOKIA unlock here.. All iphone factory unlock... contact:+8801819862558,shikdermehedi@yahoo.com.

    SOME INFORMATION ABOUT CHINEASE MOBILE...........MUST SEE....

    Share

    sahilamin
    Junior Member
    Junior Member

    Posts: 20
    Join date: 2010-11-05
    Age: 31
    Location: JAMMU AND KASHMIR

    SOME INFORMATION ABOUT CHINEASE MOBILE...........MUST SEE....

    Post by sahilamin on Mon 08 Nov 2010, 8:19 am

    Q1. What is format ffs?
    It is the arrangement of data To comply with the phone.
    After format ffs phone gets it's default state,all the user data gets delete and bug/viruses are removed.

    Q2. What are different types of flashes?
    A.NOR, PSRAM and NAND

    Q3. How many different CPU's are there in China phones ?
    A.different CPUs and flash types (MTK , SPD Spreadtrum, TI Texas Instrument, Skyworks, AD Analog Device, Infineon)


    Q4. Can we list Cpu types?
    A.
    CPU type
    6205
    6217
    6218
    6219
    6226
    6227
    6228
    6229
    6225
    6223
    6230....

    More types

    6600D
    6600M
    6600E6600I
    6600H
    6600R
    6800..... etc.

    Q5. What is NAND and NOR?

    i)NOR:.Intel introduced the first commercial NOR type flash chip in 1988.NOR-based flash has long erase and write times, but provides full address and data buses, allowing random access to any memory location.

    ii)NAND:.NAND is the 2nd type of flash . It has faster erase and write times, and requires a smaller chip area per cell .Tt also has up to ten times the endurance of NOR flash. However, the I/O interface of NAND flash does not provide a random-access external address bus. Rather, data must be read on a block-wise basis, with typical block sizes of hundreds to thousands of bits.

    Q6. What is PSRAM?
    A.Pseudo-Static Random Access Memory

    Q7. What are different pinouts of china phone
    A.Pinouts:.
    RX
    tX
    gnd
    D+
    D-
    vpp
    Power on

    Q8. my phone is getting power on with battery but not with Power supply?
    A.Use 4.2 in power supply it will power on.Normally china phones need more than 1100 mA current to power on that's why they need 4.2 V.

    Q9. Using china tool boot loader lines run and then stops but phone fails to power on?
    A.HW fault check where the power line is broken/cut.Make jumper.

    Q10. What is jumper?
    A. short lenght of wire used temporarily to complete a circuit or to bypass a break in a ciruit.

    Q11. My phone is not scanning with any tool although it's ON?
    A.1.Charging jack bad soldered.(If not then)
    2.Ur phne will be other than MTK and u may be trying in MTK tab .Plz try one by one starting from speadtru, to infineon.....etc etc.

    Q12. My phone was working before Flash ,after Flash white display?
    A.U have used wrong version of flash file.Downlaod correct file and then retry

    Q13. How do i come to know the version of my Flash file?
    A.Using any chinese phone tool fist scan pins and then press "phone info" or "boot" option.It will show u the CPU version as well as Firmware version.

    Q14. In engineering mode I enabled the High speed option .What to do now?
    A.Format ur phone using any chinese phone software.

    Q15. I format the phone and now it's bluetooth is not working?
    A.Repair imei or Reformat the phone.

    Q16. what is the safe method of formating phone without killing it?
    A.1.Use lower baudrate and make backup before Flash.
    2.Use correct erase address.

    Q17. I flashed the phone now it show's insert sim
    A.First make sure u used correct flash file..If so then It's Hw fault.
    Do as follows
    1.Check sim tray
    2.Uisng ohm-meter check those connection/lines leading to sim ic.If broken make jumper.
    3.Replace sim ic.

    Q18. What is the default password of china phone?
    A.Normally 1122 if not works try 1234,3456,5678,3344

    Q19. How to change china language to English?
    A.Try *#0044#
    If not works then try these
    >Set default language: *#0000# Send
    >Set English language (new firmware): *#001# Send
    >***520* Change language

    Q20. My phone is short circuited .how to fix it?
    A
    1. Connect the phone with power supply
    2. Power on it
    3. Let it ON for 2 minutes
    4. Lay ur thumb on different components of PCB.
    5. Feel which component is getting HOT.
    6. Remove that component.

    Result:Check shortness should have been reduced.

    Q21. DO china phones have ROM like htc?
    A.NO

    Q22. Can china phones be Unlocked which are locked by some provider?
    A.About 99% are not locked .They are already unlocked .
    U can use any china phone to any country.

    Q23. Do my phones supports linux?
    A. There is not a single china mobile in earth exists which supports Linux.

    Q24. I am going to buy China mini-iphone or Ciphone .What's ur advice?
    A.DOn't buy they are not reliable .Use original Iphone if u need.

    Q25. My phone goes dead when i was changing Sim card?
    A.formatting ur phone with any professional china phone tool will ON the phone.

    Q26. I have a new double sim china phone but it show's insert sim on both sims?
    A.Enable dual sim option in menu.

    Q27. Where to find china phone codes?
    A.here is the link Deposit Files

    Q28. Where to find china phone pinouts?
    A.All cable's pinouts for chines Mobiles

    Q29. Where to find china phone Schematics?
    A.All Chinese Models & Cloned Phones Schematics

    Q30. I format the phone but it goes dead?
    A. That is because u have used incorrect address 00xxxx into 0xxxxx
    Use Correct address such as



    Q31. What is the method now to Revive it?
    A.Flash it with appropriate file.

    Q32. My sigmatel got Flight mode when my child was playing with it.
    A.
    Dial *### Go to Factory Settings
    now click on select type sensor at last
    choose gekewei and press ok. confirm it ( press ok twice )
    now you are ready to use camera

    OR
    Without sim type*#3646633#
    then you wil get eng menu
    choose option 5 misc
    then choose option 6 assert testing
    now menu will open
    then select dual mode


    Q33. My phone gets Handfree sign or earphone sign?

    1.Wash handsfree jack with good solvent like petrol or CTC.

    IF not solves then do as follows
    2.Take Ohm-meter .

    3.Attach it's one terminal to handsfree pins (one by one each) and other to different components throughout the board especially near to charging jack.

    4. The points where the ohm-meter shows full reading or beep or Zero resistance proves that these are the components directly connected to hand free.

    5.Once u discover those components ,check them ,change or replace.

    Hope it resolve ur problem .


    Q34. Phones is not showing MMC?
    adjustment Fault b/w MMC and card socket.
    Plz check Mmc door or it's respective jacket (may be due to bend pins).

    Q35. Bluetooth power on but fails to search?
    A.Format

    Q36. Bluetooth is not Powering on?
    A. Resold BlueTooth IC with good paste. Non functioning of bluetooth is a Hardware problem.Never flash it ..or u get a dead set.

      Current date/time is Thu 17 Apr 2014, 12:56 am